Loxeal Engineering Adhesives and Sealants


Go to content

Instant Adhesives

Products

Adesivi istantanei

USE
Cyanoacrylate adhesives are formulated for the instant and structural bonding of rubber, metals, ceramic,
leather and a variety of plastics. Best results can be obtained with joint gaps of less than 0.1 mm
up to 0.2 mm for special grades. The service temperature range is between - 50 C and + 80 C,
although new high-temperature resistant formalations are available for use up to 200 C.
For porous surfaces or for vertical application a gel grade is available.

TECHNICAL INFORMATION

Adesivi istantanei

14

Instant adhesive based on methyl cyanoacrylate, medium viscosity and high strength. Especially recommended for assembling rigid materials like rubber-metal or metal-plastic, its slow setting time allows the eventual repositioning of parts.

17

Instant adhesive based on methyl cyanoacrylate, high viscosity and high strength. Especially recommended for bonding metals, rigid materials, ceramics and rubber and plastic on a metal support. High viscosity allows to fill large gaps and its slow setting time enables the eventual repositioning of parts.

23

General purpose medium viscosity instant adhesive based on ethyl cyanoacrylate. Medium setting speed. For bonding rubber, metal, plastics parts.

25

Medium to high viscosity, medium setting speed, instant adhesive based on ethyl cyanoacrylate. Designed for bonding irregular surfaces of plastic, rubber, metal, ceramic.

27

High viscosity instant adhesive based on ethyl cyanoacrylate. Designed for bonding irregular surfaces of plastic and rubber. The slow-setting time allows adjustment of parts during assembly.

29

High viscosity instant adhesive based on ethyl cyanoacrylate. Designed for bonding plastic and rubber together or with metal. High viscosity allows to fill large gaps. The slow fixture time allows adjustment of parts during assembly.

32

Super fast instant adhesive on basis of ethyl cyanoacrylate. Low viscosity, designed for fast bonding of EPDM, foam rubber, difficult to bond rubber, soft/plastic.

34

Super fast instant adhesive on basis of ethyl cyanoacrylate. Low viscosity, designed for fast bonding of EPDM, foam rubber; difficult to bond rubber, soft/plastic.

37

Flexible medium-high viscosity instant adhesive based on ethyl-cyanoacrylate. Fast cure on flexiblesubstrates, suitable for porous surfaces. Good peel strength.

41

Surface insensitive low viscosity instant adhesive on basis of ethyl cyanoacrylate. Very fast cure, even under low humidity conditions, on difficult to bond substrates, on porous and acidic surfaces as leather, wood, paper, carton, foamed rubber, EPDM.

43S

General purpose, surface insensitive medium viscosity instant adhesive based on ethyl cyanoacrylate. Insensitive to acidic surfaces, it is recommended for bonding of leather, wood and metals. Proven temperature strength up to +120C with peaks for short times up to +150C. NSF registered as acceptable for use as an instant adhesive (category P1) in and around food processing area. Registration No.154017.

45

Instant adhesive based on ethyl cyanoacrylate. General purpose, medium viscosity and acidic surfaces insensitive, it will rapidly bond also leather, wood and metals. Temperature resistant up to +100C, with peaks up to +120C for a short time.

47

Loxeal ISTANT 47 is a highly thixotropic ethyl cyanoacrylate adhesive, suitable for bonding of rubber and plastics together or on a metal substrate. Non-drip, non-sag gel, suitable for use on vertical surfaces. The high viscosity formulation and the delayed fixture time allow large gaps filling and parts repositioning. It provides proven temperature resistance up to +120C with peaks up to +150C for short times. NSF registered as acceptable for use as an instant adhesive (category P1) in and around food processing area. Registration No.154016.

48

Gel, fluid ethyl cyanoacrylate adhesive, suitable for bonding of rubber, plastics, woods and ceramics. Designed to be easily dispensed by dosing systems. Its delayed fixture time allows parts repositioning; it provides temperature resistance up to +120C.

52

Fast setting modified ethyl cyanoacrylate adhesive, with improved temperature resistance and low viscosity. Specifically suitable for bonding rubbers, plastics and metals where prolonged heat exposure is required. Temperature resistant up to +180C.

54

Loxeal ISTANT 54 is an ethyl cyanoacrylate adesive with improved temperature resistance. Specifically suitable for bonding rubbers, plastic and metals where prolonged heat exposure is required.

55

High impact strength instant adhesive. Suitable for rubber, plastic and metal joints. High temperature resistant and medium viscosity formulation for common gaps filling. Low setting time allows easy and correct positioning of the parts to be bonded.

60R

Very low viscosity instant adhesive based on alcoxy-ethyl cyanoacrylate. Specifically formulated for 3D printing applications, as a print Infiltrant for strengthening printed models produced with 3D printing technology based on powders/granules. Very low viscosity and delayed curing time allows good depth of penetration into parts and a wicking effect. Usage of Loxeal 60R helps not only to strengthen the parts, but to achieve a smooth and good aesthetic appearance too. Alcoxy-ethyl formulation reduces blooming effect and it is clear, low odour and non-irritating.
Especially suitable to be used in non-ventilated or closed areas (no powdery residue and no heating).

63

Instant adhesive on basis of alcoxy-ethyl cyanoacrylate. Low odour not irritating, non blooming effect for appearance sensitive assemblies. Especially suitable to be used in non ventilated or closed areas. Delayed setting time allows adjustment of parts during assembly.

67

Instant adhesive on basis of alcoxy-ethyl cyanoacrylate. Low odour not irritating, non blooming effect for appearance sensitive assemblies. Especially suitable to be used in non ventilated or closed areas. Delayed setting time allows adjustment of parts during assembly.

73

Rubber toughened low viscosity Ethil-Cyanoacrylate adhesive with increased flexibility and impact resistance. Suitable for bonding rubbers and metals. Curing time is designed to allow right positioning of the pieces before assembly. Good temperature resistance up to 120C.

74

Rubber toughened low viscosity Ethil-Cyanoacrylate adhesive with increased flexibility and impact resistance. Suitable for bonding rubbers and metals. Curing time is designed to allow right positioning of the pieces before assembly. Good temperature resistance up to 120C.

75

General purpose high viscosity Ethil-Cyanoacrylate adhesive with superior peel and impact resistance. Suitable for bonding rubbers, metals and plastics.

77

Toughened, high viscosity Ethyl-Cyanoacrylate adhesive with improved flexibility and impact resistance. Suitable for bonding rubbers, metals and plastics. Good temperature resistance up to +120C.


Back to content | Back to main menu